Gabor Designer Series
Heat Friendly Synthetic Lace Front Mono Part Wig
Fiber Type: Tru2Life Heat Friendly Synthetic Hair
Cap Style: Lace Front, Monofilament Part
Cap Size: Average
Length: Front 9" • Crown 11" • Nape 8 1/2" • Side 10 1/2" • Back 11 1/2"
Weight: 4.6 oz.
Color Shown: GF14-22SS SS Wheat • GF132SS SS Sangria
Long sleek layers in a mid-length cut create the look of length. Ageless and effortless. Easier to maintain and flattering for women of all ages. An extended lace front lets you wear half up or brushed away from the face with a beautifully natural-looking hairline. You will easily Own The Room in this youthful, seductive style
- Ear-to-ear sheer lace front
- Monofilament part
- Velvet-lined ear tabs
- Velvet-lined extended nape
- Resilient stretch material throughout the cap base for a custom-like fit
Gently remove tangles with fingers or a wide-tooth comb. Start at the ends and slowly work toward the roots to avoid damage. Do not brush.
- Add a small amount of HairUWear Shampoo to a washbasin of cool water. Use shampoo sparingly.
- Place product in washbasin and allow it to soak for 5 minutes. Do not scrunch or agitate the product.
- Rinse by holding under running cool water until the water runs clear. Gently squeeze or use a clean, dry towel to press out excess water. Do not twist or wring.
- Apply a light mist of HairUWear Leave-in Conditioner + Detangler avoiding the base and roots. Applying conditioner to the base may cause shedding.
- Place wet wig on a folding HairUWear Wig Stand or hairpiece on a HairUWear Hanger until it is completely dry.
- Shake and style with your fingers to achieve the desired look. We recommend a HairUWear Styling Brush, HairUWear Styling Comb or fingers to style.
- Apply a light mist of HairUWear Leave-in Conditioner + Detangler to difficult tangles if needed.
- Heat-friendly synthetic fiber can be curled, blow dried or flat ironed to achieve a different hairstyle.
- Heat-friendly synthetic fiber can withstand heat up to 350°F/180°C. We recommend a low-medium setting.
- Style as desired:
To straighten, take a 1 inch section starting at the roots and run a flat iron to the ends.
To curl, wrap the hair around a curling iron and hold for 10 seconds. Carefully slide the iron out and pin the curl in place. Once the fiber has completely cooled it will keep the curl until heat is applied again.
If desired, use HairUWear Hair Spray on the final styled product.
Tips & Tricks
- Soaking longer than the recommended time will damage the product.
- Hot water will damage heat-friendly synthetic fiber.
- Sudden bursts of heat, such as opening an oven door, will damage heat-friendly synthetic fiber.
- Do not dry on a solid form or mannequin head to avoid stretching the cap.
- We do not recommend sleeping, showering or swimming during wear.
- Store the wig on a HairUWear Wig Stand or hair piece on a HairUWear Hanger to avoid unwanted kinks or crimps.
- Lace is delicate and should not be tugged or pulled.
- After extended wear, matting and frizz can occur. To smooth, wash, condition and spray with HairUWear Leave-in Conditioner + Detangler then blow dry with a HairUWear Styling Brush.
- Heat-friendly synthetic fiber can withstand heat up to 350°F/180°C. We recommend a low-medium setting. Fiber will be damaged if the heat setting is too high. We do not recommend curling or straightening the hair while wearing. Heat-friendly synthetic fiber will get very hot.
- Any cutting should be done by a professional hair stylist. No returns or exchanges will be allowed for worn or altered products.